Piboon Concrete HOLLOW CORE SLAB
Hollow core concrete slabs are used as general building floor structures. It is lightweight compared to other types of structures. It has its own strength and can be used to support weight immediately without any temporary support.
Type of use
Suitable for homes, townhomes, commercial buildings, office buildings, department stores, warehouses and industrial plants.
product
Sizes of prefabricated hollow core slabs: thickness from 8, 10, 12, 15, 20, 25 and 30 (cm.) width sizes from 60 and 120 (cm.)
service
- Installation and delivery service
- Ready to give advice on installation work
- Free site survey service
feature
- It is light in weight compared to solid sheets. Save on supporting structures from beams, columns, foundations, and piles.
- Hollow floor slabs are produced from modern machines with high compressive strength. This allows the hollow floor slab to support weight better.
- lighter weight High quality and efficiency Prefabricated hollow slabs are sound and temperature insulating slabs made from prestressed concrete with a strong surface and wide hollow holes.
- Can be used to run electrical wires and water pipes.
Instructions and precautions for use
There can be problems if the floor has to be drilled later. This is because the prestressing wire may be cut and the floor slab may have problems with water leakage between the joints if the concrete is not poured thick enough or the slope is not adjusted well to the point of water retention. Therefore, it should not be used on bathroom floors or rooftops. including the basement
โครงการบ้านพักอาศัย
|
|
อาคารสำนักงาน
|
|
อาคารสำนักงานราชการ
|
1. เมื่อจะเข้าทำการวางแผ่นพื้นสำเร็จรูป ผู้ก่อสร้างควรที่จะตรวจสอบปรับระดับหลังคานที่จะวางแผ่นพื้นให้ได้ระดับและสะอาดเรียบร้อยเสียก่อน เพื่อการวางแผ่นพื้นจะทำได้สะดวกรวดเร็วและเพื่อป้องกันการแตกร้าวของแผ่นพื้นด้วย 2. นำแผ่นพื้นสำเร็จรูปมาจัดวางเรียงชิดกันโดยตลอดตามแบบที่ระบุไว้และถ้ามีเชียร์คีย์ (Shear key)ควรจะเชื่อมก่อน ต่อจากนั้นควรยาร่อง รอย ต่อระหว่างแผ่นพื้นทันที เพราะหากปล่อยทิ้งไว้อาจมีเศษวัสดุตกลงในร่อง ซึ่งยุ่งยากต่อการเก็บขึ้นภายหลัง 3. ผูกเหล็กตะแกรงขนาด 6 มม. เป็นตะแกรงระยะห่าง # 0.20 ม. ที่ส่วนบน แล้วเทคอนกรีตทับหน้า (Topping) หนาตามที่แบบกำหนด ใช้อัตราส่วน 1:2:4 โดยปริมาตรและให้มีกำลังอัดประลัยไม่น้อยกว่า 210 กก/ซม2 แล้วปาดหน้าให้เรียบหรือขุดสากหากจะปูกระเบื้อง 4. หลังจากเทคอนกรีตทับหน้าแล้วควรบ่มน้ำหรือบ่มวิธีอื่นๆ ต่อไปอย่างน้อย 24 ชม. |